Hopp til hovedinnholdet

Publications

NIBIOs employees contribute to several hundred scientific articles and research reports every year. You can browse or search in our collection which contains references and links to these publications as well as other research and dissemination activities. The collection is continously updated with new and historical material.

2024

To document

Abstract

Phenol-formaldehyde (PF) resins can be impregnated and cured in situ to improve the woods dimensional stability and decay resistance. In search of renewable alternatives, the substitution of phenol by lignin cleavage products (LCP) has been discussed. However, the different chemical nature may affect the performance of the resin against fungal decay, formaldehyde emission, and equilibrium moisture content. In this study, 30 % (w/w) of the phenol in PF resins were substituted by LCP obtained from microwave-assisted pyrolysis. Scots pine sapwood was modified with the resin. The decay resistance against Rhodonia placenta, Gloeophyllum trabeum, and Trametes versicolor was determined. Additionally, effects of specimen organisation within the Petri dish, different substrates, length of leaching, and type of inoculum were studied. Further, the materials water vapor sorption properties and formaldehyde emission were determined. All modifications effectively reduced fungal decay. With 10 % weight percent gain (WPG), initial decay was detected, while 20 % WPG and 30 % WPG provided efficient protection. The substitution of phenol increases the formaldehyde emission. While further reduction in formaldehyde in the resin admixture or formaldehyde scavengers may be required, the method described herein can be used to partly replace fossil-based phenol, while maintaining good fungal resistance.

To document

Abstract

Heat treatment increases the decay resistance of wood by decreasing its hygroscopicity, but the wood material remains degradable by fungi. This study investigated the degradation of heat-treated wood by brown rot fungi, with the aim of identifying fungal-induced hygroscopicity changes that facilitate degradation. Scots pine sapwood samples were modified under superheated steam at 200 and 230 °C and then exposed to Coniophora puteana and Rhodonia placenta in a stacked-sample decay test to produce samples in different stages of decay. Sorption isotherms were measured starting in desorption from the undried, decaying state to investigate their hygroscopic properties. Although there were substantial differences in degradative ability between the two fungi, the results revealed that decay by both species increased the hygroscopicity of wood in the decaying state, particularly at high relative humidity. The effect was stronger in the heat-treated samples, which showed a steep increase in moisture content at low decay mass losses. The reference samples showed decreased hygroscopicity in absorption from the dry state, while the heat-treated samples still showed an increase at low mass losses. Near infrared spectroscopy showed that the early stages of decay were characterised by the degradation of hemicellulose and chemical changes to cellulose and lignin, which may explain the increase in hygroscopicity. The results provide a new perspective on brown rot decay and offer insight into the degradation of heat-treated wood.

To document

Abstract

Automated sorption balances are widely used for characterizing the interaction of water vapor with hygroscopic materials. These instruments provide an efficient way to collect sorption isotherm data and kinetic data. A typical method for defining equilibrium after a step change in relative humidity (RH) is using a particular threshold value for the rate of change in mass with time. Recent studies indicate that commonly used threshold values yield substantial errors and that further measurements are needed at extended hold times as a basis to assess the accuracy of abbreviated equilibration criteria. However, the mass measurement accuracy at extended times depends on the operational stability of the instrument. Published data on the stability of automated sorption balances are rare. An interlaboratory study was undertaken to investigate equilibration criteria for automated sorption balances. This paper focuses on the mass, temperature, and RH stability and includes data from 25 laboratories throughout the world. An initial target for instrument mass stability was met on the first attempt in many cases, but several instruments were found to have unexpectedly large instabilities. The sources of these instabilities were investigated and greatly reduced. This paper highlights the importance of verifying operational mass stability of automated sorption balances, gives a method to perform stability checks, and provides guidance on identifying and correcting common sources of mass instability.

To document

Abstract

The global packaging sector has grown consistently, and the use of sustainable materials, including recycled and biodegradable products, is expected to rise. This study focuses on the potential of producing barriers for water and water in moist air (water vapor) from proteins to protect cellulosic materials. Owing to the specific requirements of packaging materials, the main subject of this research was their barrier and strength properties. The scope of this work includes selecting components and their physicochemical treatment to produce functionalized coatings on sprayed paper and pure films, as well as film-coated samples (paper laminated with film). The following tests were used to estimate the hydrophobic, hygroscopic, and strength properties: Cobb absorption, contact angle testing, dynamic vapor sorption, and dynamic mechanical analysis. In most cases, the spray-coated paper and film-coated samples absorbed less liquid water than untreated paper. Wheat gluten protein was the most effective water barrier. In all variants, the vapor sorption, desorption, and hysteresis effects (or the lack thereof) showed significant differences compared to those of cellulosic materials. All variants of the spray-coated and film-coated samples in the dynamic mechanical analysis showed an increase in the strength properties of the samples in comparison to the untreated paper. The increased humidity caused a significant loss in the mechanical properties of all variants, exceeding the strength loss of the untreated control samples.